AHU-SELECTION GUIDE

 Air Handling Unit (AHU) Selection Guide

https://www.systemair.com/fileadmin/user_upload/systemair-b2b/Support/Media_Center/Air_Handling_Units/AHU_SBA-BA_2018.pdf

Introduction:

Selection of AHU includes the type of AHU, filters, coils, panels, fans, and a few other components. Any change in specification of these items directly affects the performance, quality, capacity, and cost of the air handling units. This document explains various terminology and standards used in the industries at the macro level. The readers are advised to refer to the latest standards & manufacturer data to get specified accurate information.

Click here for Air Handling Unit (AHU) performance calculation.

Types of AHU

  • Horizontal floor mount - All major components are aligned to the base tray and it makes maintenance-friendly.
  • Vertical floor mount – Designed to occupy less space
  • Ceiling suspended – Hanged from the ceiling inside the “false ceiling” and zero floor space
  • Draw Thorough type: Blower after the filter, coils and all
  • Blow through type: Blower before all.

A typical AHU consists of the below components in place

Filters

European Standards EN 779& EN 1822

These standards are describing the classification & characteristic requirement of filters used in building ventilation & industrial process.

Based on the particulate size it classifies the filters as below

  • Classes G1, G2, G3 & G4 – Defining the requirement of coarse dust particulate size > 10µ
  • Classes M5, M6, F7, F8 & F9 - Defining the requirement of fine dust particulate size 1µ - 10µ
  • Classes E10, E11, E12, H13, H14, U15 & U16 – Defining the requirement of suspended particulate sizes <1µ

Based on the type of filtration the filters are grouped together as below

  • Coarse filter requirements are defined under classes G1-G4 of E 779
  • Medium filter requirements are defined under classes M5-M6 of E 779
  • Fine filter requirements are defined under classes F7-F9 of EN 779
  • High-efficiency filter requirements are defined under classes E10-U16 of EN 1822

ISO 29463

It is derived from EN1822 and both are based on MPPS – Most Penetrating Particulate Size. MPPS is the particulate size at which an air filter gives minimum arrestance. But they have some differences in leakage test methods. Both standards are describing the requirement for high efficiency EPA, HEPA & ULPA filters.

ISO 16890

It replaces EN 779 from the year 2018. The EN 779 classifies the filters based on the filtration efficiency of particulate matter size of 0.4µ. Whereas ISO 16890 classifies the filters based on a spectrum of particulate sizes from 0.3µ to 10µ. It has three major classifications used by WHO (World health organization) as below

PM1 – Particulate sizes less than 1µ

PM2.5 – Particulate sizes less than 2.5µ

PM10 – Particulate sizes less than 10µ

The particulate matter >10µ are not breathed, the particulate matter <10µ can penetrate bronchi, the particulate matter <2.5 µ can penetrate pulmonary alveoli and the particulate matter <1 µ can penetrate alveoli capillary barriers.

European standard EN 15805

It describes the header framing dimensions of filter used in air intake systems and air handling units.

MERV–Minimum Efficiency reporting value

It is described in ASHRAE 52.2 to report the effectiveness of filters. It classifies the filters from MERV1 to MERV16. Higher the rating filters will allow fewer dust particles. This standard is intended to assist the end-user and specifier in their selection of appropriate filters for various applications.

Coil

All standard values in this document are referring to water as tube side fluid. Please refer AHRI 410 & ASHRAE standard for other fluids.

Chilled water details:

As per AHRI 410: 2001 the acceptable range of values are

  • Chilled water inlet temperature 35° F ~ 65ׄ° F
  • Water velocity - 1 fps ~ 8 fps
  • Minimum fin surface temperature >32° F
  • Minimum tube surface temperature >32° F

Typical values are

  • Chilled water in & out temperature 45° F & 55° F
  • Estimated Δt - 10° F
  • Chilled water pressure drops - max. 20 ft H2O
  • Flow rate - 2.4 gpm/ton
  • Water velocity – 2fps~3fps

An increase in flow rate causes the velocity & pressure drop to increase. Then the water stays very little time inside the coil, which causes the air leaving temperature to grow and gives a reduced air Δt. To achieve the required air temperature and coil performance we may have to increase the number of fins/ft, which results in a price increase for the coil.

The maximum pressure drop across the coil falls between 20 ~ 24 ft H2O. But it is advisable to keep as low as possible and typical values fall less than 10 ft H2O. The pressure drop in the coil is controlled by the number of tubes in the coil.

The size, length & width of a coil is decided based on the fin length, design air face velocity, and required tonnage of the coil.

Fins

Aluminum is the standard material for fins used in most applications. Copper fins are recommended for corrosive environments. The number of fins various between 8 fins/inch to 14 fins/inch based on the heat transfer requirement.

When there is an increase in water flow rate the heat transfer rate reduces across the coil due to higher velocity, which requires fewer fins/inch. The required number of fins/inch will be close to 8. There will be a decrease in price for the coil, but we will end up with higher velocity & pressure drop.

Typical aluminium fin thickness falls between 0.006” ~ 0.0095”.

Tubes

With ½” tube OD, the performance will be increased slightly, and not a major difference between 5/8” tube OD. Like tube OD with an increase in tube thickness, there will not be a big difference in performance, only the coil life can be improved. The typical thickness for coils is 0.025” ~ 0.035”.

Number of rows in coil

A typical number of rows of a coil for AHU is 4. An increase in the number of rows results in more Δt, low discharge air temperature, more moisture removal& higher dehumidification & more air pressure drops for the fan.

Typically, an increased number of rows will be used where the intake to an AHU is 100% fresh air, like operation theatres.

Drain pan

A drain pan for individual coil section is expected, because the condensation in the upper coil may block the airflow in the lower one. And the main drain pan is required at the bottom of the full coil, which drains out the water.

Reynold’s number of an AHU coil is dependent on the tube inner diameter, fluid velocity & tube type. Reynold’s number can be controlled based on the circuit & adding a turbulator. Adding a turbulator may result in a higher pressure drop.

Refer latest AHRI 410 for the method of calculating Reynolds number and acceptable values.

Fouling

Fouling is the formation of sediments and any other matters that form inside the tube over a period. Fouling increases pressure drop reduces heat transfer, and obstruct fluid flow.

There is no straight method to calculate the fouling and it is the value directly added to thermal resistance for design & manufacturing of coil. This defines the duration for cleaning frequency.

The unit of fouling is ft²-°F-ht/Btu. Value zero will be considered for fouling when possible and the typical value will be 0.0005 for internal & 0.001 for external.

Air side details

As per AHRI 410: 2001 the acceptable range of values are

  • Air face velocity – 200 fpm ~ 800 fpm
  • Entering air dry-bulb temperature – 65° F ~ 100° F
  • Entering air wet-bulb temperature – 60° F ~ 85° F

Typical values are

  • Air face velocity – 500 fpm
  • Entering air dry-bulb temperature –65° F ~ 80° F
  • Entering air wet-bulb temperature – 60° F ~ 70° F
  • Estimated Δt - 20° F ~ 25° F

When the air face velocity is too low heat transfer will not take place due to lack of turbulance. At the same time when the air face velocity is too high, the heat transfer will be very less with a higher air pressure drop. Also, moisture carry-over will happen at high velocity which results in water droplets all over the AHU. The air pressure drop will be very minimal at 400 fpm of face velocity, but there will be a slight increase in the cost of the AHU.

With the increased number of coil rows and fins, we get a higher air pressure drop.

As a rule of thumb 400 cfm is considered for 1TR capacity in a typical AHU. Refer to performance calculation for more details.

ASHRAE standard 33 – defines the equations for calculating air side pressure drop, sensible cooling, dehumidification, and test requirements.

AHU Panels

Outer skin & inner skin are usually made of galvanized steel. Aluminum and stainless steel materials are considered as alternate for specific requirements.

The insulation is selected based on the required thermal resistance & sound attenuation.

Single skin AHU

  • Mainly for ventilation
  • Outer casing shall be of – 0.5mm thick; with powder coated.
  • Insulation of 25mm thick fibre glass or 15mm foam
  • Suitable for lesser flow up to 2200 cfm

Double skin AHU

  • Mainly for air conditioning
  • Inner Skin – 0.4~0.7mm thick; galvanized steel
  • Outer Skin – 0.4~0.9mm thick; with powder coated
  • Insulation of 50mm thick fibre glass or 25mm foam; insulation is sandwiched between inner skin and outer skin.

Fans

Forward curved fans

Backward curved fans

Forward curved fans will have many small blades curved in the direction of rotation.

Backward curved fans will have less quantity of longer blades curved opposite to the direction of rotation.

Flow is tangent to the rotation

Flow is in radial direction

Requires a scroll house to convert the kinetic energy into static energy

No housing is required

Smaller in size for a given air flow

Larger in size for a given air flow

Single inlet is suitable for high pressure low volume Double inlet is suitable for high volume, low pressure system

Suitable for higher efficiency & high pressure

Can run with AC motor

Requires an EC motor

Typically, forward curved fans are used in AHUs due to the operational requirement, cost & size.

Operating above or below the optimum design criteria can cause noise and reduce the efficiency of the system for both forward & backward curved fans.

Internal static pressure (ISP) = Total pressure drop caused by all components within the system, like., filters, coils, mixing box and other components.

External static pressure (ESP) = It is the pressure developed in supply/return system / ducting, like., duct pressure loss, volume control dampers, diffusers, and other components.

Total static pressure (TSP) = ESP + ISP

Each component (filters, dampers, diffusers, grills, ducts, etc) in the given system produces some static pressure to the fan. The static pressure to the fan is directly proportional to the flow and at the same time, the fan cannot be operated above or below the optimum levels.

Additional information

Additional details to be considered in selecting an AHU are given below and we are not covering in this article.

  • Drip eliminator,
  • Anti-corrosive coating to the coil
  • Variable frequency drives for fans
  • Humidifiers
  • De-humidification
  • Belt drive / Direct dive for the fans
  • Selection of pulley and belts
  • Volume control dampers
PROVIDED BY FACTORY: FOR SAMPLE (FROM SYSTEM AIR)


OUTER SKIN : 0.6 MM thick pre coated GSS INNER SKIN: 0.6 MM thick PAluzinc sheet

FRAMEWORK : Extruded aluminum Section with/without thermal break profile DRAIN PAN: 18 G Stainless steel(Single Skin) with 13mm nitrile insultion INSULATION:Polyurethane foam

PANEL THICKNESS:50 MM

FAN: NICOTRA make DIDW Backward curved centrifugal blower

 

CONFIGURATION OF HORIZONTAL FLOOR MOUNTED AIR HANDLING UNITS:

Mixing box section with manually operated(FA&RA) AL dampers.

Filter section with 50 mm thick EU-4 filters and 300mm thick EU-7 filter on common GI filter frame Cooling coil section with 6 row deep (12.7mm OD copper tube) CHW cooling coils.

Fan section with NICOTRA make DIDW Backward curved centrifugal Fans with drive packages and with drive motors.

 

NOTES:

1.      The face velocity across all types of filters & coils has been considered as 500 FPM

2.      The cooling coils will be made of 27 G copper tubes(12.7mm OD) having aluminum fins with MS header and GSS casing.

3.      We have included for std EEF-1 motor in all the units.

4.      PO to be released on Systemair India Pvt Ltd, Plot No. 03, Sector 31, Ecotech-1, Kasna, Greater Noida - UP - 201308'

EXCLUSIONS:

3-way mixing valves, modulating motors, thermostat, pressure gauges, guide vanes, thermometer gauges, DP nozzles, all types of grills, PG device, speed regulator switch, ASP, other controls and instrumentations, ducting, electrical cabling, louvers, valves, strainers, testing, commissioning, installation and other accessories

Comments

Post a Comment

Popular posts from this blog

Valves- Definition, Differences and Applications

Valves, Definitions and Applications 1.       Ball valve : used instead of butterfly less than 32 mm diameter: Is used to regulate the flow. 2.       Butterfly valve : used to control the flow and used instead of ball valve for > 32 mm 3.       Gate valve: it is used to completely turn off or turn on the flow which ball valve and butterfly valve is normally not used for 4.       Check valve: used for unidirectional flow and avoid back flow. Used normally in discharge line of pumps and where flow happens when certain pressure difference forces for back flow. Provided in the supply side of the machines to prevent backflow into the machine. It does not have any handles or whatever. So, it is easier to recognize. 5.       Strainer: mostly provided at inlet of the machines to avoid the waste enters the machine and damage t...
Read more

Efficiency Booster- For anything

Are you tired of trying to hard trying to save project or goals from falling apart? I was. So, I have come up with some ideas that will help in managing the stress retaining the efficiency your work demands. Below I have listed some of them. If you have some, let me know in the comment section. 1. To make any work efficient,  Break down the work into many smaller steps.   2. Which steps are repeated often? Try to automate or use easier tools for the work. 3. Which Steps requires more time and attention? Use efficient tools and manpower. 4. There are some items or actions that may seem insignificant but the work cannot be moved forward without them.  5. Make the decisions regarding the things that take a long time. For example, if the project needs airplane after some months and You need to order from others. Otherwise, the decisions will linger and it will be out of our control.  6. Create work schedule for the works and break down the work for example, if the p...
Read more

Electrical Load- Transformer allocation

Image
    ELECTRICAL LOAD CALCULATION CHILLER PLANT 0.5 kw  per ton  is an “annual average  chiller -plant efficiency.” For Example, 300 TR,  power consumption in kW= 324*.5    = 1.5 In the below Example, 300 TR of chiller Consumes the 193 kW of Energy. The water cooled version has a full load efficiency of about 0.7 kW/Ton. The air cooled version has a full load efficiency of about 1.1 kW/Ton. For example, if the system had a pump with a known efficiency of 65 percent and the pump delivers 250 gallons per minute to a total head of 72 feet, the horsepower of the system is: Hp = \frac{250\times 72}{3,960\times 0.65} = 6.99\text{ horsepower} H p = 3 , 9 6 0 × 0 . 6 5 2 5 0 × 7 2 ​ = 6 . 9 9  horsepower In the above Example,  efficiency is 80%. H p = 3 , 9 6 0 × 0 . 6 5 816×50 ​ =15.85  Hp =15.85X.746 =11.8 kW Chiller Cooling Tower: 350 TR cooling tower Fan consumes 22.38 kW. Rule: 6 CFM per Watt AHU:  375 CFM PER TON Electrical POWER C...
Read more